DIY gift ideas are given to us by life itself. Life in the city takes place in a special rhythm, which forces you to do several things at the same time. So, many people have a snack, not looking up from work at the computer. However, hot dishes can damage the surface of the table. To prevent this from happening, you should purchase a stand for a hot cup or ... you can make a hot stand with your own hands.

In addition, such a little thing can be presented as a gift to a loved one or girlfriend. A do-it-yourself stand will not only fulfill its intended purpose, but will also become another reminder of warm feelings.

For a do-it-yourself stand you will need:

• two old disks;
• the cloth;
• thin foam rubber or other material that can be used as a lining;
• a bag of beads;
• scissors;
• a small piece of satin ribbon;
• needle and thread.

Step 1

Fold the fabric in half with the front side inward. We place a disk on the surface, retreat two centimeters from its outer edge and draw a circle. This can be done in two ways. Firstly, with the help of a compass, and secondly, with the help of a ruler.

Step 2

Carefully cut out the circle along the resulting line. Since the fabric is folded in two layers, it is necessary to ensure that these layers do not move (otherwise the edges will turn out to be uneven). It is advisable not to tear off the lower blade of the scissors from the surface of the table, this technique will help to get the most even cut.

Step 3

Foam rubber or other soft material(for example, you can use an old knitted sweater) you need to cut out two circles, the diameter of which will be equal to the diameter of the discs.

Step 4

The resulting blanks must be folded as follows: in the center of a larger diameter circle we place a smaller one, and put a disk on it.

Step 5

The edge of a circle cut out of fabric is sewn with ordinary stitches, which are located at a short distance from each other. Then the edges of the fabric are pulled together with a thread. You need to tighten so that the fabric tightly fits the disc and lining. Similar steps must be taken to obtain the second half of the future stand.

Step 6

From satin ribbon cut off a piece about five centimeters long. We fold it in half, and sew the edges of the resulting loop to one of the blanks.

Step 7

The resulting blanks are folded together so that the side on which the disk is visible is inside. After that, the halves are neatly sewn together. To make the seam invisible, you need to choose threads that match the color of the fabric, and also try to make small stitches.

Step 8

The seam can be masked with beads. This will require a special needle to work with the specified material. It has a small eye that can pass through the narrow hole of the bead. So, we fix the thread, string six beads on the needle, and fix the thread again. We continue to sheathe the seam according to the indicated pattern until we finish the circle.

Work completed. Now you can safely put a cup with the hottest coffee on your desktop without fear of damaging its surface.

Such hot coasters can be seen in large numbers in the Crimean souvenir stalls. They are made from juniper and they diverge very quickly. In conditions middle lane juniper, of course, cannot be found, but it is very easy to make such a stand with your own hands from tree branches with a beautiful pattern on a saw cut. These are acacia, apple, plum, apricot, oak and ash.

In an hour, you can make several of these coasters. To begin with, we need to pick up branches 3-6 cm thick. You can combine saw cuts from branches of different thicknesses, it will be beautiful.

It is most convenient to cut a branch into saw cuts 4-5 mm thick with a miter saw:

But you can cut saw cuts with a hacksaw for wood. It is advisable to sand each cut from the front side with sandpaper.

The bark can be peeled off with a knife, but this is not necessary, especially if the bark is tightly adjacent.

Now we combine the stand from saw cuts different diameter(in my case). Front facing inward:

However, it should be borne in mind that the fewer links, the easier it will be to glue the stand. It is desirable that the tree rounds adjoin each other at several points. We glue together the links of the stand, laying saw cuts on top of several circles. To do this, we coat at the junction with PVA glue:

After making sure that all the links are linked together, we send the stand to dry under pressure. I took a linen bag of sand, put it on a stand and put another bucket of water on top. The stand is glued together in 4-5 hours.

There is another option for making a wooden hot stand. We cut out a circle from the matting and glue the cut branches on it on both sides. It turns out very stylish and beautiful. It's also easier to do this:

Please rate this post:

If you are a fan of needlework and creativity, then you will be interested to know how a do-it-yourself hot stand is made. It is easy to make from materials available in the house. Even a beginner can master the execution technology. So, get acquainted with the options, choose your favorite.

Do-it-yourself hot stand: interesting ideas

If you decide to make such a souvenir, first of all, decide which method suits you best. It will depend on your personal preferences and skills. Stands can be:

• from wood;
• sewn from fabric using the patchwork technique;
• crocheted;
• made of felt;
• made on the basis of computer disks, buttons;
• made using decoupage technique on ceramic tiles or wooden blanks.

Any of the ideas is easily finalized and has many options and interpretations. Choose, add, create.

Use saw cuts of trunks and branches

A do-it-yourself hot stand made of wood, made of round pieces of the same or different diameters, turns out to be very beautiful. It is not difficult to prepare them, an ordinary saw and a suitable tree are enough. The saw cuts of apple and cherry trees look good, as they have an original structure. But you can choose any option you like.

The technology of work is as follows:

1. Prepare saw cuts of branches with a diameter of 5-6 cm. If the bark fits snugly against the wood, it can not be removed. Be sure to sand the front side of the rounds until smooth.
2. Make a composition of cuts. The fewer parts, the stronger the product will be. In any case, the parts must be in contact with each other in several places.
3. Connect the joints with glue.
4. For greater strength, the stand can be made of two layers. Accordingly, the saw cut planes are also connected with glue.
5. Leave the workpiece for several hours under load until the product is completely dry.

Everything is ready! If desired, varnish the surface, although the natural texture is no less beautiful.

Another way is to use one large saw cut, which can be decorated with burning, carving, contour drawing, watercolor ornament, followed by varnishing. If you do not know how to draw, use decoupage (the technology will be described below). As you can see, one material can be used in different ways.

We sew a souvenir

Do-it-yourself hot stand made of fabric is also sewn different ways. There are a lot of ideas. First, decide on the size and shape of the product. It can be a souvenir of the appropriate diameter, as well as a full-fledged rug or napkin. Both those and other options are performed in the form:

• vegetables;
• fruits;
• berries;
• colors;
• animals;
• fairy tale characters;
• abstract patterns in the technique of patchwork.

If you have ever made potholders, then the technology is similar here. The product is made of two layers of thin fabric with a dense material between them.

Felt is of particular interest. It is easy to work with, as it does not require overlaying the edges, because this material does not crumble. In addition, it is quite dense, and when using several layers of felt, folded one on top of the other for decorative purposes, no additional layer is required. Felt is used to make coasters in the form of slices of oranges and lemons, animal faces, hearts and any other plots. This material is represented by a rich colors bright colors, so the field for imagination is large.

Beauty from old CDs

When making a stand, you need to consider that it must be dense, durable and resistant to temperature. If you are going to use a thin fabric on the front sides, you definitely need a dense base.

A do-it-yourself hot stand can be made very simply from computer disks that will play the role of a blank. The technology of work is as follows:

1. Take two disks and cut out circles from the fabric that are a couple of centimeters larger in diameter.
2. Lay the disc on the fabric blank with the wrong side to the disc (you can also lay a layer of padding polyester).
3. On the perimeter of the circle at a small distance from the edge (1 cm), sew the stitches, and then pull the threads. The disk will turn out "sewn" inside. Do the same with the second blank.
4. Take a strap of a length that is equal to the perimeter of the disk. Sheathe the part with braid, or ribbon.
5. Connect all three elements by sewing two "covers" on the strap.

The product is ready. Fast, simple and beautiful.

Knitted fantasy

A spectacular and original do-it-yourself hot stand can be made using this technique. As a rule, all products are knitted in the round according to the napkin principle.

To make such a souvenir, it is enough to find the appropriate pattern, yarn and hook. If you are good at this technique, you can knit any product even without a diagram. Some people like to tie existing blanks, for example, the same computer disk, covers, corks, beads. Flowers and fantasy geometric shapes are assembled from small details.

Decoupage

This technique is suitable for those who are remotely familiar with needlework or have little experience, but want to immediately get a masterpiece.

The meaning of the work is that on a dense base of saw cut wood or, for example, ceramic tiles(previously cleaned and degreased), a napkin (special or single-layer table) with a decorative pattern is glued. After drying, the surface is covered with glue in several layers or varnish. The reverse side of ceramic tiles is covered with a layer of glued felt or fleece.

So, you saw how a hot stand is made with your own hands. Choose what is closer and more interesting to you. Create table decorations or simply original gifts from improvised materials.

Beautiful wooden coasters under the hot can be an excellent gift for any holiday. These handmade items will decorate any table and are sure to attract everyone's attention. Making original coasters is not at all difficult, you just need to make a little effort.

Before starting work, you need to prepare:
- six wooden blanks (they can be cut out of plywood yourself or purchased at a specialized store);
- watercolor;
- pencil;
- acrylic lacquer;
- brush with synthetic bristles No. 3 (for coloring);
- a round brush with synthetic bristles (for applying varnish);
- eraser;
- a device for burning;
- container with water.

Having prepared everything you need, you can start creating coasters:

1. On the first blank, draw a dahlia and a border around the edges with a pencil;

2. On the second blank, draw a border and draw a rosehip flower;

3. On the third stand, depict strawberries, daisies and a border;

4. On the fourth blank, draw a raspberry and a border;

5. On the fifth stand, depict a branch of mountain ash, lingonberries and a border;

6. On the sixth blank, draw a wild rose and a border;

7. Turn on the burner and wait until its tip heats up. Then carefully burn out the contours of the dahlia and the border on the first blank;

8. Burn out all the rest of the coasters, carefully circling the pencil outlines with the tip of the burning device. Then turn off the device and erase all pencil lines with an eraser;

9. Prepare your watercolors for work by lightly wetting them with water. Then color the stand, which depicts a wild rose. To make the color more saturated, apply several layers of paint to the flower petals. Paint over the border with light brown paint;

10. Color the second stand, which shows strawberries and chamomile. On the leaves, mix green and yellow paint to achieve smooth color transitions;

11. Paint the dahlia blank. Paint the tips of the flower petals with white paint, and their main part with pink;

12. Then paint the workpiece on which the twig of mountain ash and lingonberries are burned;

13. Color the stand on which the raspberries are burned;

Pleasant little things, made by hand, add warmth and comfort to your home. Such things create a unique atmosphere, and also bring many joyful moments in the process of working on them.
The kitchen is the most comfortable and sought-after place in the house. After all, it is in the kitchen that we spend a lot of time cooking, washing dishes or having heart-to-heart conversations with a cup of tea. In order not to damage the surface of your favorite table or expensive kitchen worktop hot bottom of a cup of tea, we need a stand for hot. If you are a creative person, then you will come up with many ways to make such a stand. This small kitchen accessory can be knitted, carved from wood, or woven from a wicker. Let's look at three simple ways making coasters for hot dishes on the table. Most likely all the right materials you can easily find at home.

Making a hot stand from discs, coarse linen thread and wine corks

A cork coaster is a popular handmade version of this kitchen accessory. We suggest you make such a stand in an easy and fast way.

For needlework we need:

• 2 unnecessary CDs;
• a sheet of thick cardboard;
• several meters of coarse linen thread;
• corks from wine, about 15 pcs;
• a good glue that can stick a linen thread to plastic (you can use Moment Crystal).

We cut out a round blank in the shape of a disk from cardboard. We make a “sandwich” with glue: the first layer is a disk, the second is a cardboard part, the third is a disk again.

While the blank dries, cut the corks in half. We should get 30 halves. We try to ensure that the segments of the corks are the same length.

We lay the linen thread on a round blank. To do this, in the center of the part, to the cardboard, which is visible through the hole in the disk, we glue the tip of the thread. Then we wind the thread in a spiral, gluing it in the course of work, until we cover the entire surface of the disk. You can make a side if you glue several new turns of thread along the edge of the workpiece to the already formed ones.

Then, using the same glue, we fasten the cut corks in a circle. We are waiting for the glue to dry.

Now we know how to make easy-to-make cork coasters.

How to make a hot stand from an unnecessary computer power supply

Surely many have preserved at home old, already broken parts from the computer. Now we will learn how you can easily and quickly make a stand from an unnecessary power supply for a computer. If you don't have this part, don't worry. Perhaps one of your friends has such a treasure, or there is a service center for the repair of digital equipment nearby, where you can purchase a non-working power supply for a nominal fee or a simple “Thank you”.

The manufacturing process is very easy. It is necessary to unscrew the cover of the block and bend its side walls inward. This is a job for a man, because some physical effort is required. After the stand is ready, it can be decorated. For example, paint with acrylic paints.

Such a stand will withstand any, even very hot surface.

Stand for hot from a wooden base and piece aquarium pebbles

Very beautiful hot coasters are obtained from piece aquarium pebbles. Usually they are made of glass. And glass can crack at high temperatures, so you can’t put a pan that has just been removed from the fire on such a stand. But a mug of hot tea or a plate of delicious soup will look great on it.

List of required materials:

• wooden base for the stand;
• piece aquarium pebbles;
• acrylic paint to match the stones;
• primer to wood.

First you need to cut it out of the board or purchase a wooden blank of the right size. You can show your imagination and choose something else as the basis, for example, a “sandwich” made of disks and cardboard, as at the beginning of the article. But square coasters decorated with pebbles look more interesting. Then we prime the workpiece. We wait until the primer dries, and paint acrylic paint. The color of the paint should be in harmony with the stones. Final stage- we put our aquarium decor on glue. You can use the same "Crystal Moment".

Our coasters are ready to perform their function.

Making coasters for hot dishes is a fascinating and creative process. If you have a lot of ideas and no longer need coasters at home, you can make a small gift for your friends. They will definitely like the original hot stand. The master class published on our website will help you master the exciting process of making DIY kitchen accessories.

(Visited 3,993 times, 1 visits today)

home » gable » Coasters for hot from improvised materials. Hot stand: do it yourself from different materials