Can a person lift a toilet alone. How to raise the toilet higher

Or a toilet, most people are faced with such a problem that the outlet level of pipes of plumbing fixtures changes. This happens as a result of changing the level of the floor and rearranging the equipment. One way or another, in this case, the question arises of how to raise the toilet higher. In this article, we will give you practical tips on how to deal with this problem with your own hands at minimal cost.

How to raise the toilet? There are several approaches to solving this issue.

To eliminate the problem of incompatibility of fittings, you just need to use modern adapters. If you are faced with the fact that the axis of the pipeline does not match, you should use a flexible hose system or create a new pipe gasket. The level of the future location of your plumbing depends on how these holes coincide.

To achieve the necessary matching of the nozzles, you can use one of three options:

create a new installation site at which the appropriate level will be maintained;
install a hanging toilet;
apply a system of adapters and nozzles.

Beginning of work

Before any work, it is necessary to properly prepare workplace. In our case, everything that is not related to the installation should be removed from the room. It is best to work in a completely empty room. To change the product level, you will need:

chisel;
a hammer;
wrench;
level;
felt-tip pen;
screwdriver;
Bulgarian;
sandpaper;
device for pumping water (rubber pear);
sealant;
cement and sand;
washers, bolts and so on.

Sequencing

Before looking for an answer to the question of how to raise the toilet, you must disconnect it from the sewer and water supply. To do this, it is necessary to shut off the water supply and disconnect the main pipe on one side from the tank, and on the other - from the water supply. Next, take care to extract all the remaining water from the product. To do this, you will need a rubber bulb and a regular rag. If you leave even a little water inside, it will spill out during transportation.

As it becomes clear, you can find the answer to the question of how to raise the toilet yourself. If you have ever encountered a similar problem, share your comments below this article with the readers.

When, as a result of back pain, it is difficult to sit on the toilet due to the standard height, the question arises of how to raise the toilet higher. In this article, we will practical advice how to raise the toilet with your own hands and improvised materials.

Before dismantling the toilet bowl and preparing a place for a new installation, it is necessary to determine the height of the rise. To do this, put improvised objects on the toilet and determine the height of the lift.

We disconnect the water supply and sewerage from the toilet bowl by shutting off the water. We remove the water remaining in the toilet bowl with a rag. The toilet is fixed on wooden stand using self-tapping screws. The exit from the toilet to the sewer is made of a corrugated adapter. To disconnect, we tighten the corrugated pipe. We turn off the bolts and remove the toilet bowl.

Toilet Raising Material:

To raise the toilet you will need
Foam block of required thickness
Glue for foam block
dowel nails
Silicone
Putty on drywall

Do-it-yourself toilet lifting

We carefully place the toilet bowl on the foam block and trace the lower contour with a marker. Then, using a hacksaw, we cut out our stand in the foam block. We try on the resulting workpiece and process the irregularities sandpaper to visually become one with the toilet.

Now we will prepare the base for installation by cleaning the place of dust, leveling the surface under the toilet bowl. Having tried on the workpiece, we apply the adhesive to the floor and fasten the part to be glued after waiting one minute.

We remove the remaining glue, and with the help of a level we level the surface of the podium. Let our construction dry according to the instructions of the adhesive composition. self-tapping screws. Further in the reverse order as dismantled.

We putty the podium with putty on drywall, and we can paint it in the color of the toilet. This design is reliable and does not spoil appearance.

How to raise the toilet higher when renovating a bathroom? Typically, the need for such work arises when changing the level of the floor and rearranging plumbing fixtures. In this case, it will be useful to know the methods for performing such work on your own.

Stage one: choosing options

In order to raise the toilet a little higher, it is necessary to combine its outlet with the outlet of the sewer pipes. This can be done in several ways:

Use a flexible plastic accordion. This will allow you to install the toilet at any desired height, but the reliability of the entire system will depend on the quality of the plastic accordion, and the device itself will be pushed forward a little, which is not always convenient for small toilets.

You can try to match the output axes of the device and sewer pipe selection of the appropriate angle of the nozzles and the use of gaskets. This is not always possible, since often the angles of inclination are of such magnitude that it is difficult to select standard nozzles for them, and one has to make a composite structure.
In order not to have problems with inconsistencies in the angles of the pipe, you can redo the sewer outlet so that a hanging toilet is installed above the floor.

After a person decides and chooses the most suitable of these three options, you need to prepare tools, fixtures and materials, and then proceed to implement the plan.

Second stage: workflow

First you need to prepare the workplace. To do this, remove all things that may interfere with the installation of the device on a new floor. The best option when there are no objects in the bathroom or toilet.

The production technology is as follows:

First, the toilet is disconnected from the water supply and sewerage system. To do this, shut off the water supply to the tank of the device, close the central valve and remove the hoses going to the float on the tank.
It is necessary to remove all the water that remains there from the device. To do this, use a rag and a rubber pear.
Then remove the fasteners on the sole of the device. Usually the toilet is mounted on a wooden board or concrete screed. If the old fasteners cannot be removed, then they are cut off with a chisel and a hammer.
After that, you can disconnect the device from the sewer. To do this, remove the outlet of the device from the sewer pipe.
old cement coating must be removed.
It is recommended to thoroughly clean all pipes from dirt and old seals.
After the floor in the room is raised to a new level, you need to put the toilet on wooden bars in the location chosen for installation. The horizontalness of the surfaces is checked by the building level.
If it is not possible to accurately align the exit axis of the toilet device with the sewer pipe, then it is best to use a flexible plastic accordion. In some cases, it is better to use rubber corrugation. Sometimes it is possible to make a sufficiently acceptable adapter from two standard pipes (for example, 135 ° each), which will allow you to accurately align the axes of the sewer pipe and the outlet of the toilet bowl, but then you will need to take care of good sealing of the joints.

Then it will be necessary to fix the toilet on the new floor. The base of the device is circled with a felt-tip pen, the attachment points are marked, and then holes are drilled. The device is fixed with bolts or dowels.
Fix the whole system. To do this, you can use cement and sand. Increasingly, many people attach the toilet to the floor with silicone adhesive, but this is not always convenient. Sometimes a foam block is used, as it is easy to cut with a hacksaw.
After these works, it is necessary to connect the tank of the device to the water supply network using hoses.

Suspension installation

When changing the level of the floor in the bathroom or toilet, modern experts recommend installing a hanging toilet.

This can be done in two ways:

The installation is being created.
Is being done concrete base.

The first method involves the construction of a special structure that allows you to change the level of the device and helps to fix it. With such a system, the toilet is precisely aligned with its drain pipe with the sewer. The installation can be covered with drywall.

To create a concrete base for a hanging toilet, you need to purchase 2 steel studs with an M20 caliber and a length of 0.8 m. You will also need wood screws, formwork ( wooden planks or sheets of plywood), washers, nuts, concrete mortar.

At the first stage, it is necessary to install an adapter between the sewer and the toilet. After that, the attachment points of the studs in the wall are determined. It is better if the holes are drilled through. If this cannot be done, then you will have to use epoxy glue. The formwork should have 2 side and 1 front planes. The studs will pull it to the wall, and then they are used as supports for the hanging toilet.

Concrete must be poured gradually so that the adapter does not move. The formwork should stand for 7 days until the concrete dries. All connections of the toilet device must be treated with sealant.

After the complete installation of the suspended structure, it is necessary to connect it to the water supply network. Although the complexity of the installation is quite high, the service life of such a design is quite long and reaches almost 40 years.

Required materials, fixtures and tools:

Flexible accordion.
Sewer pipes and gaskets.
New hanging toilet.
Cement and sand, concrete, boards.
Epoxy adhesive.
Sealant.
Washers, bolts.
Bulgarian.
Building level.
Rubber pear (it is needed for pumping water).
Chisel and hammer.
Wrench (it is better to use an adjustable version).
Sandpaper and knife.
Screwdriver, tape measure, felt-tip pen.

All of these methods of raising the toilet are easy to do with your own hands. But if a person does not have time to do this or he does not know how to do it, then it is better to call a plumber. True, in this case, the financial costs will be much higher, but the quality of work will be higher.

If you plan to make drastic changes to the bathroom, it is better to do this while the general renovation is underway. Modernization is possible, but in practice it may raise questions.

The outlet of the plumbing must match the part where the outlet of the sewer pipes is located. This must be taken into account before the ascent.

There are several options for solving the problem.

When an accordion is used, plastic, flexible in shape. Then it is allowed to choose any height for installing the toilet. But the quality of the harmonica determines how high quality the whole structure will be. For the device, some front extension is important, this option is not convenient for everyone. The boiler is not affected.

Sewer axes and outlets from the device are easily combined, and if you choose the right angle of the nozzles, use gaskets. This is not always possible in practice. After all, initially the angle of inclination is such that the selection of something else causes problems.
It is possible to alter the sewer outlet for water to meet the wishes.

After choosing one of the options, it remains to take care of the selection of tools and materials. Then go directly to the plan. The water heater does not need to be touched.

Description of the workflow

The first step is to prepare the workplace for mixers and other items. The main thing is to get rid of everything that will interfere with the installation of the device.

The technology is usually used as follows:

The toilet bowl and plumbing, sewerage are disconnected from each other. The water supply to the tank of the device is blocked. The central valve must be closed, the hoses from the float on the tank are removed.
The remaining liquid is removed from the device. A rag with a rubber pear will help to cope with this. This is also required for the faucet in the bathroom.
The mount is removed from the sole of the device. The most commonly used screeds are made of concrete or wood. Remove the fasteners with a chisel and hammer if it is impossible to do this in other ways.
You can disconnect the device and the sewer from each other. Disconnect the outlet from the pipe.
The old cement coating is removed.
Pipes require complete cleaning of contaminants.
The next step is to raise the floor to the required level. In the place chosen by the owner, the toilet is mounted on top of wooden bars. The building level helps to understand how horizontal surfaces are. It also helps in the case when the gasket is replaced with an analogue.

The best choice if the axes do not align exactly is a flexible accordion based on plastic. Sometimes a rubber corrugation becomes a worthy replacement. Using two nozzles, normal adapters are created. But then you have to ensure normal sealing for the joints.

At the final stages, the toilet bowl is fixed on the floor surface. The attachment points are circled, as is the base itself. Marking improves the accuracy of work. After that, it remains to drill holes.

The system is fixed. Cement and sand will suitable materials to solve the problem. Many use silicone glue when attaching, but this option is not always convenient. The foam block is convenient only in the sense that it is easy to cut it with a hacksaw.

When the work is completed, it remains to connect the tank to the water supply.

Suspended structures: installation procedure

This issue is solved in two ways - with the help of installation or a concrete base.

In the first method, a special design is created that changes the level of the fixture in height and secures it. Installations are easily fixed with drywall. Everyone will figure out how to raise the toilet higher.

To construct a concrete base, you can not do without additional materials.

You will need:

Two steel studs, caliber M20, 0.8 meters long.
Screws for wood.
Formwork.
Washer.
Screw.
Concrete solution.

The transition sleeve connects the toilet and the sewer - this is the action of the first stage. After that, they determine the place to which the studs will be attached to the wall. The best way- drilling through. If this option is unacceptable, proceed to the use of epoxy glue.

Two side and one front surface are required for formwork. The studs help secure it to the wall. Then these same parts become the support for the wall-hung toilet.

Concrete is poured gradually, then you do not have to worry about the displacement of the adapter. The formwork is left for seven days, until the concrete dries completely.

Sanitary and hygienic standards

What does the law say? Construction, sanitary and hygienic norms and rules establish a number of restrictions associated with the transfer of plumbing. Damage from leaks and noise should be kept to a minimum.

The following rules help you figure out how to lift the toilet under any circumstances.

directly above living rooms and kitchens, bathrooms should not be located. This is valid only for apartments in two levels. Thanks to this norm, the lower rooms are protected from possible flooding.

Often, when repairing a bathroom, there is a need to raise the toilet bowl higher above the floor. This may be caused changing the level of the exit of pipes, floor, location of plumbing and other reasons.

Basic ways to raise the toilet higher off the floor

Raising the toilet above the floor level is carried out in several ways:

Creating a new place to install the toilet with the appropriate level is a complex process, with a partial restructuring of the engineering system of the apartment.
Installation of a new suspension type product- a common solution to such a problem, which requires additional installation, possible restructuring and dismantling of engineering sewer systems.
The erection of a pedestal- it is used less often, as it requires certain skills in finishing work, special materials and dry mixes (if the podium is made of cement or concrete). Task can be greatly simplified if foam blocks are used for the podium.
The use of special plastic gaskets- a frequently used option, which is chosen due to the simplicity of functionality and installation, availability and popularity. Suitable for occasions when it is required to temporarily create a certain height toilet in connection with physical features person (for example, children, the elderly, people with disabilities living in an apartment with other tenants).
Through pipes and adapters- just like in the first option, you will have to spend a lot of time and effort on conducting plumbing work for connecting pipes and changing the plan of utilities in the apartment.

The choice of the appropriate method depends on the skills and abilities of the owner of the apartment, as well as on the situation and the reasons for which such work is carried out.

Plastic toilet seats and spacers to increase height

A simple and affordable way to raise the level of the toilet. Allocate children's coasters, which help a small child sit on a large toilet, as well as classic adults - for the elderly and people with handicapped .

How do they look

The stand is frame with seat desired shape and height. If necessary, it can be equipped with a step. In some cases, a special type of consoles is used, which has more complex shape and a separate control system.

Photo 1. Children's coasters, which will help a small child sit on a large toilet, are often sold as a set of a seat and a step.

Advantages and disadvantages

The advantage of stands is that no need to dismantle plumbing. They are suitable for models of all types and shapes. Stands are used in cases where people living in an apartment need different level toilet height. With linings easy to change the height and configuration of the toilet seat, as well as significantly increasing the level of convenience and comfort for each family member.

The disadvantages can only be attributed to the fact that more complex lining with handrails or a step may take extra bed in the toilet room.

How to install

The installation of the prefix depends on the type of construction. general principle is that the product is placed on the bowl of the product or above it. The person using it will need to sit down not on the toilet itself, but on this stand.

In general, the installation process is quite simple and the user will only need to study the instructions that come with the product.

How else can you raise the toilet higher: pedestal

Installation of a pedestal for the concept of a toilet bowl involves the dismantling of a plumbing device followed by placing it in the same place, but only at a slightly higher height.

What can it be made from

Often pedestals are made from cement and concrete mortars. In addition, there is a tendency to make pedestals from foam blocks. This method is the easiest to perform.

Photo 2

How to install it

To start calculate the lift height and select the foam block in size, it will form the basis of the future podium. Then the toilet is disconnected by removing the corrugated pipe leading to the sewer and unscrewing the bolts that attach the device to the floor.

Important! The toilet is disconnected from the water supply and sewerage. Before that need to turn off the water.

The contour of the lower part of the product is outlined on a piece of foam block of a given height. Then the part is cut out and applied to the base for comparison. I process the edges of the workpiece to an even state. The finished element is glued to the floor. After the glue dries, the toilet is placed on the resulting podium and fixed with dowels. The edges of the pedestal are aligned under the toilet so that the design does not look like an alien element, but looks harmoniously as a natural continuation or part of the plumbing.

Attention! Important straighten the edges so that the pedestal merges with the toilet. Subsequently, if this is not followed, the appearance of misaligned edges will draw attention.

home » Attic » Can a person lift a toilet alone. How to raise the toilet higher