How to close the front door after installation. Sealing slopes after installing the front door - how to seal and sheathe on metal

Many owners prefer to do repairs in the apartment with their own hands, especially at the stage of solving design problems. A modern man boldly orders the metal base of the front door, independently deals with artistic coating and installation, significantly saving family budget. This is the only way out in cases where it is difficult to combine the interior of the front door with the interior of the corridor.

How to cover the front door

Decorating the house from the outside, the master takes into account a wide range of air temperatures in summer and winter, fluctuations in humidity levels depending on precipitation and other operational features. The probability of damage to the door leaf inside the house is almost minimal, the influence of natural factors is limited. Material selection suitable for decorating the interior of the corridor, presented on the construction market in a large assortment.

It is necessary to carefully study the instructions and the procedure for performing installation work, taking into account the peculiarity of the location of the rooms. Perhaps it is better to highlight the central entrance so that it differs from other openings. The design with mirrored glass looks spectacular. An illusion appears free space in a small corridor.

solid wood panels

The most expensive type of wooden lining for decoration metal frame are oak slabs. The high price of wood is justified by its advantages:

Panels can be ordered directly from the machine, and painted by yourself, choosing the desired shade. After a few years, the top coat of varnish is recommended to be applied again to give a new shine to the whole house. In today's construction market presented arrays of 40 species of trees.

Laminate

Laminated planks are a multi-layer material that is great for interior decoration entrance door. Laminate has become a popular interior decor because it does not require special skills during the installation process, it is easy to assemble into a single canvas. Care without special requirements, dirt is easily removed with microfiber, a damp cloth.

Planks are technically easy to connect with profiles, contours, decorative elements any complexity. First, the master makes accurate measurements, then, separately from the metal frame, he assembles a solid laminate shield. In turn, the plates are mounted on the canvas, because often the shape of the door is not perfectly rectangular. Sometimes you have to deal with intricate cutouts, voluminous elements.

Wooden lining

High-quality material is universal, massively used in construction. To decorate doors, it is recommended to use lining made of coniferous wood. Pine and spruce has a number of advantages:

less expensive;
exudes a pleasant forest aroma;
has a natural antimicrobial effect due to phytoncides;
beautiful wood pattern fits any design idea.

The lining is easy to assemble into a single canvas due to special locking joints, while you can create any direction of the jointing line.

Leatherette

Finishing work using artificial leather remains relevant in modern design interiors of houses and apartments. The main advantage of the material is the relative cheapness. It is easy to sheathe any design with dermantine No expensive tools or glue required. The result of the work is the high quality of the top layer of the front door.

Dermantin has a lasting color, while it is possible to choose any shade necessary for implementation design solution. The material does not evaporate toxic substances, repels water drops, and does not deform under temperature changes. Leather substitutes are resistant to fire. They are easy to care for, just wipe the surface with a clean, damp cloth.

Plastic panels

Polyvinyl chloride is often used for cladding metal door. PVC has established itself in the construction market as a high-quality waterproof material that does not absorb moisture, retains its shape, appearance and lasts for a long time. The plastic panel does not rot, does not crack in conditions of temperature difference in summer and winter.

Thin, even layer close to the main surface, without gaps, forming a continuous decorative surface. A wide choice of textures and colors meets any design needs. With proper care, plastic panels last for many years without losing their original luster.

Combinations are especially popular. different materials in door decoration. The elements are securely attached to each other, taking into account the quality and stylistic compatibility. To perform work of high complexity, it is necessary to have additional tools and means of fastening.

How to finish the slopes of the front door from the inside

The luxury of oak and the brilliance of gold fittings will spoil unattractive slopes, their shape and appearance must be carefully thought out in order to organically fit into the overall environment without losing functionality. Cosmetic work begins with the repair of the base layer.

The plaster will have to be leveled, cladding, for example, with drywall, if the future decor is light. Drywall won't last on its surface of bricks. AT difficult cases alabaster is added to the plaster to make it especially durable.

The pattern and texture of the slopes can repeat the design of the walls in whole or in part. The method of pasting slopes does not differ from working with walls in an apartment. To fix laminar panels or MDF, you need to prepare a perfectly flat surface, especially if the slopes are wide. In narrow areas, the panels hold better. At the same time, the mounting foam securely fixes the decorative material.

In the light of modern fashion trends the design of the slopes of the front door inside the apartment using artificial stone looks stylish and rich. This is a durable decor that does not require special care. A variety of textures and colors allows you to create a unique artistic composition, imitating rough masonry. Compared to natural stone artificial material much lighter, reduces the load on the main structure.

slope decoration decorative stone produced in several stages. To create desired shape in the chosen style, a variety of layout schemes are used, therefore, a sketch is determined in advance. The material is attached to liquid nails or polyester resins.

Wooden slopes in classical style remain popular today. Big variety colors and shades helps to perfect any interior, gracefully and unobtrusively. The disadvantages of wooden slopes include the need to update the top layer more often than other materials. But dignity natural wood far outweigh this flaw.

The most economical option for decorating the entrance is considered to be a plaster layer. Without prior experience, the opening can be plastered in a few hours with high quality and reliability. From above, paint of any color is applied, combined with the interior of the corridor. Plaster is also used in emergency cases to gain time before overhaul, For example. Experienced craftsmen call plaster the most reliable and in a simple way finishing works.

Doorways are extremely rarely decorated with plastic, because this is a zone of increased physical influence, and plastic is not a very strong and durable material. But if the door is covered with PVC on top, then perhaps the PVC panel will be the only suitable material for slope decoration.

Before finishing work doorway carefully checked for sealing in the joint area, areas with suspected air leakage are foamed. Then the excess foam is cut off, cleaned and covered with a primer.

Slope repair is an interesting activity that requires responsibility. Correctly selected material, taking into account operational features- the key to a successful labor-intensive process.

Installation of entrance doors provides reliability, safety and high-quality protection against heat loss, all kinds of external sounds and noises. If a person is engaged in repairs in his own apartment on his own, next question, which he will have, will be about how to fix door slopes with your own hands.

No matter how carefully the door is installed, you can hardly do without additional finishing of the slopes.

From the outside, the doors are most often closed by craftsmen, or people close them themselves during the installation process. With inside everything is much more complicated. There will be bare concrete, door fasteners, bricks and so on. In order to hide all this disgrace, you will need to make door slopes.

It is worth knowing that the process of finishing the slopes of the entrance doors can be done with the help of installers, but not every company is ready to undertake this. Therefore, you will need to make slopes with your own hands.

This process is not at all complicated with any method of forming slopes.

Back to index

Instructions on how to make slopes on the front door yourself

Elements that will be needed in order to make the slopes of the entrance doors:

The appearance of the slope after the installation of the door. In order to hide defects, you will need to make door slopes.

The material that will be used as cladding (drywall, laminate, MDF, plastic panels, and so on).
Film and masking tape.
Deep penetration plaster.
Beacon profiles.
Gypsum solution.
Cement-sand mortar.
Drill with mixer nozzle.
Self-tapping screws.
Wooden bars or slats.

Back to index

Existing ways to perform slopes

The main purpose of the drywall slope is to give a normal look to the doorway and secure fastening cover. door frame. Thus, it will be possible to increase the burglary resistance of the entire structure. There are several ways that people can form slopes themselves:

Seal with mortar and plaster.
Glue the finishing material with a solution.
Perform frame sheathing with finishing material.

Separation should be made specifically according to the method of slope formation. This is due to the fact that it will be possible to choose a wide variety of materials for sheathing. Slopes can be made of drywall, laminate, MDF, plastic panels, wooden lamellas, cellulose panels and many other materials. The choice must be made based on how you plan to fix the slope of the front door with your own hands.

The most acceptable option in terms of sound insulation and protection is to seal the entire slope with mortar. In addition, the result will be a slope that does not bend and has no voids. However, in terms of design this option somewhat cramped. A good solution may be to decorate the slope with textured plaster and paint.

In the event that, in addition to filling with a solution, various finishing materials are mounted, it will be possible to achieve absolutely any appearance. Therefore, this option, with high-quality performance, combines the advantages of the first method and does not have any disadvantages.

It is important to understand that without high-quality slopes, even the most beautiful door able to lose all its charm.

The last way to slope the front door is based on mounting finishing material, for example, MDF, drywall or plastic, on an already pre-built frame, which people can make themselves from wooden bars or a metal profile.

Such an option may be ideal in the case when a sufficiently large amount of mortar is spent on slopes using other methods to completely fill it. As a result, it will be possible to save some money, in addition, you can make the slope more aesthetic. It is worth knowing that with a frame structure it is much easier to achieve evenness and comply with all levels, and this is very important for visual perception.

Using this slope option can be great for installing lights and switches in or above a doorway. Thus, it will be possible to illuminate the hallway at the entrance to the apartment itself. In addition, at frame structure it will be much easier to conduct such communications yourself, such as, for example, the Internet or cable television.

Back to index

Performing all necessary preparatory work

It is worth noting that the preparatory stage is the same for any method of forming slopes. First of all, you need a door frame and door leaf cover with tape and masking tape to avoid any damage. It is necessary to cut off all particularly protruding parts that may interfere with the process of mounting the frame of future slopes or protrude above the level of plastering.

After that, the entire surface is swept and primed. It is important to note that in this case the best option will use a deep penetration primer. It is relevant to use a surface primer only if the wall is made of some kind of loose material (for example, foam concrete).

At this stage, it is worth thinking about how to carry out laying power cable to connect the switch that you will need to turn on the lamps in the hallway. In the event that the plans use the option with frame fastening of slopes, it would be better to postpone the laying of the wire until the frame is installed.

Back to index

Performing the process of plastering slopes

With a frame construction, it is much easier to achieve evenness and observe all levels.

On a primed and prepared surface, you will need to install beacon profiles. They will make it possible to bring a flat surface to the solution that is applied. It will be possible to fix the beacons with the help of a solution. In this case, it will be relevant to use a gypsum mortar, because it sets quickly, therefore, you will have to wait much less before proceeding to the next step.

It is necessary to put in two or three places along the length of each of the ends of a pile of solution of small sizes, and then install beacons. Using a bubble level, you need to adjust the position of the beacons in the same plane.

After the mortar under the beacons hardens, it will be possible to start filling the slopes with a cement-sand mortar. Cement with sand must be mixed in a ratio of 1: 4, then thoroughly mixed with a mixer nozzle, which is inserted into a drill at low speed. The solution should turn out like a curd mass. As needed, you need to add a little gypsum.

Using a spatula and trowel, you need to apply the solution to the slopes of the doorway and level it with beacons. The solution will dry for at least a day. After it dries, it will be possible to start applying the starting and finishing putty. The final dried putty will need to be finally leveled with an abrasive mesh. Next, you need to cover the slope with paint.

Back to index

Formation of slopes with a finishing material for mortar

Materials such as drywall, MDF, plastic slopes and so on are strengthened with a cement-sand mortar or adhesive composition. After that, the surface is ready: smooth and primed.

The technology of applying the adhesive composition on a sheet of drywall.

It is best to mark the level of future slopes and provide a good support for the skin material. To do this, you need to screw the screws into the wall so that their caps form a single plane. In this case, it is necessary to take into account the thickness of the sheathing material, because it will be based on the caps of the self-tapping screws. Next, it will be possible to fill the entire space of the slope with a solution along the perimeter.

In order to save money and for reliability, a cement-sand mortar can be used as the first layer, with which you can form a layer slightly smaller than the height of the supporting screws. Next, you need to choose adhesive composition which is suitable for the selected sheathing material. Adhesive words will need to be applied in an even layer on the surface of the slopes and on the strips of material on the reverse side.

Next, you need to carefully attach the sheets of material to the slope, and then press them until they rest against the caps of the self-tapping screws. The evenness of the installation can be checked with a level. If necessary, you can correct the position if the mortar has not yet set.

In case there is a gap between the sheathing sheets and the wall, it will need to be sealed with mortar. Next, you can attach the platbands.

New doors have been installed, rubbish has been swept up, and only the slopes for the entrance doors break the idealistic picture of a fresh renovation. Not always the companies that install the doors undertake to repair the slopes - the pleasure of putting the finish line in the repair in this case fell to you!

Do-it-yourself front door slopes - what to do?

If from the outside the doors are a complete composition with platbands, then inside the apartment the view is far from ideal: gray concrete, mounting foam, bricks and fixtures. All this disgrace will help to hide the internal slopes of the front door - a section of the wall bordering the entrance from the end. Fortunately, this process can be performed according to several scenarios, and you just have to choose which one will be the most understandable and accessible for you to complete.

Set slopes to front door people try for two quite understandable reasons: to give a finished look and, more importantly, to hide the fastenings of the door frame, on which its resistance to burglary depends. There are several ways to form slopes: sheathing with a finishing material on a previously prepared frame, grouting and plastering, gluing finishing materials. Finishing materials can be very different: the usual drywall, laminate, wooden lamellas, cellulose panels and much more.

Sealing the slopes of the front door with cement or putty mortar is the most effective in terms of sound insulation and insulation.

In addition, this option is most acceptable in terms of protecting the door structure - a burglar will have to make a lot of noise to find fasteners under a layer of cement. By itself, the mortar finish does not have a special visual appeal, however, decorative finishing materials can be mounted on the mortar layer, achieving any effect, or textured paint can be applied.

The simplest and fast way- installation of finishing material on a frame made of a metal profile or wooden bars. In addition to simplicity, it is also economical, especially in cases where too much mortar is required to seal the slopes. This option allows even a person far from construction to achieve a perfectly flat surface. The frame slope is the only solution in cases where you want to install lighting and switches directly in doorway. Do not forget about the possibility of hiding the “traces” of communications in the frame - wires and cables.

Installation of slopes of the front door - the preparatory stage

Whichever finish you choose, preparatory work will be the same. First you need to protect the door leaf and frame with masking tape, but it is better to cover the entire surface with a film. And only then proceed to leveling the base - if individual sections protrude too much, they need to be cut off, and also get rid of all loose materials that are too loose.

With a broom or a brush with a fairly coarse bristle, we sweep dust from all cracks and cracks, sweep every centimeter of the base thoroughly, especially if you decide to finish with a solution - the adhesion strength of materials depends on this. Further, the surface is primed with deep penetration compounds. However, foam concrete or similar loose material should be primed with a conventional surface primer.

At this stage, you can lay electrical wiring under the switch or provide a through hole for the cable - for this purpose, you can fix an aluminum tube at the very bottom of the plinth with a slightly larger diameter than the diameter of the cable, through which you can later lay it. If you plan to get by with the formation of a frame, then you will have to tinker with the wire after it has been created.

How to close the slopes of the front door - plaster

When the gypsum composition under the lighthouses has hardened, start kneading the cement-sand mortar in a standard ratio of 1 to 4. The sand for the mortar should be well sifted, without debris and lumps, the cement should be M400. It is necessary to mix the components with a construction mixer or a drill with a special nozzle at low speeds. The consistency of the finished solution should be at the level of the density of the curd mass. If you know how to work with the solution quickly, then you can add a portion of gypsum.

A wide spatula and trowel are the main tools for the master plasterer, without which he cannot level the surface. Having slightly moistened the base with water to increase the adhesion of materials, apply the solution to the slope and align with the beacons with a spatula. A day later, you can apply two layers of putty - the main and finishing. The last layer is sanded abrasive mesh. What to do with the slope after that - leave it as it is, paint it or cover it with a finishing material - it's up to you, all options are acceptable.

How to make slopes of the front door on the frame - a quick way

The preparatory stage, described at the very beginning, is not canceled - although we do not use any solutions, we need to prime the surface. In the future, this will prevent it from shedding. To create a frame, you will need metal profiles used to create plasterboard structures, or wooden blocks. Both should fit snugly against the wall, so the surface should be fairly flat.

To strengthen the structure, jumpers are installed on the main load-bearing elements, especially at the corners between the sides of the opening and the upper plane. Then wires and cables are laid. If you use drywall for sheathing, it is enough to fix it around the perimeter with self-tapping screws. To hide the junction of the drywall and the wall, you can fill it with mortar, but it is easier and faster to cover it with platbands. Be sure to install perforated corners at the edges, and seal the joints with a special tape. It remains only to putty the surface and level it with a fine grater.

Medium-density MDF boards have better aesthetic and technical qualities. Fixing the panels can be carried out both with the help of self-tapping screws, and with the help of small nails, if the crate is wooden. Fasteners should be distributed along the edges or in other places that you plan to cover with trim and corners. You can fix the latter on liquid nails.

By the same principle, you can finish the surface of the slopes with a laminate or parquet board. It is somewhat easier with them - nails can be hammered into locks, this will not interfere with a high-quality connection. So all fasteners will be securely hidden from prying eyes, except that the corners will still have to be hidden behind the corners.

Slopes for entrance doors - a combination of materials

If you are not a master at leveling surfaces, this method is just right for you. The essence of the method is to attach the finishing materials not to the frame, but to a layer of cement-sand mortar or glue. To do this, the slopes for the entrance doors must already be leveled and primed. It is also necessary to mark the slope level and provide a stop for finishing materials. For this purpose, screws or self-tapping screws are screwed into the surface so that their caps form one straight line. Consider the thickness of the solution and the thickness of the finishing materials themselves, so as not to miscalculate with the overall dimensions of the slope.

Then we knead the solution according to the instructions already described above and fill the entire slope space with the finished mixture. To be more reliable, we recommend that the cement-sand mortar be brought out a little less than to the level of the hats, as evenly as you can. Let it harden properly (at least 1 day) and apply an adhesive solution to the surface.

Also apply glue to the reverse side of the finishing material. After attaching the trim sheets to the slope, lightly press them down so that they rest firmly on the surface and the air between them and the cement layer is released. Using the level, find out if you managed to set the sheets evenly, and while the glue has not hardened, correct their positions. Then you can attach trim and corners, if any.

After installing a new front door, it remains to update them with brand new slopes. They can be included in interior design different ways, drywall, laminate, MDF, PVC sandwich panels, as well as non-standard materials (for example, imitation of natural stone) are suitable for decoration. In order not to spend money on the services of a specialist, you can do the installation of slopes yourself, following the instructions.

Slope plastering

Slopes are plastered most often together with the entire apartment when the finishing is not completed.

Required tools:

Putty knife.
Level.
Master OK.
Rule.
The grid is painting.
Painter's tape.
Painting corners.
Construction mixer.

Materials:

Plaster (dry mix).
Finishing putty.
The primer is liquid.
Sandpaper.
Water based paint.

Do-it-yourself plastering sequence:

Clean the surface.

Prime.
Install and fix beacons with a level.
Close the junction of the wall and the slope according to the level with a paint corner.
Tape the front door and box with masking tape

Attach the mesh.
Make a solution.
Seal potholes.
Apply the solution to the entire surface, stretch along the beacons, then wait for drying and repair the cracks.
Prime.
Level with finishing putty.
Wait for it to dry and sand it down with fine sandpaper.
Paint with water emulsion.

Finishing completed.

If we are talking about a private house, it is advisable to treat the cleaned opening with an antifungal primer before work and add a little to the solution itself.

Drywall slopes

Drywall is a popular material for finishing the slopes of the front door with your own hands. It is inexpensive, reliable and easy to install.

Necessary materials:

Drywall.
Dowel.
Self-tapping screws.
Profile guides.
Glue.

Required tools:

Drill.
Roulette.
Simple pencil.
Rag.
Level.
Putty knife.
Construction mixer.
A hammer.

The procedure for doing the installation of slopes with your own hands using drywall:

Clean the opening from dust, remnants of mounting foam.
Drill connectors for dowels at a distance of 20 cm along the perimeter - it is necessary to improve the adhesion of the material to the surface.
Using a tape measure, measure the width and height of the door opening and cut out the guides: two side and one top.
Stepping back from the door hatch about 1.5 cm, attach a guide to the screws so that its narrow edge is in the inner part of the slope.
Measure the size of the strips for slopes and cut from drywall. When cutting, try to ensure that the edge of the drywall does not crumble and is even.
Dilute the glue to a state of homogeneous, thick sour cream.
On the cut parts of the drywall, apply a sticky mass in heaps.
Lubricate the dowels with glue.
The drywall sheet is inserted into the guide and pressed.

Check the level of the slope, then fix it for 6 hours.
Wipe off protruding adhesive with a rag.
Periodically tap the surface with a hammer through the trim.

The next day after installation, the slopes can be further processed: putty, paint.

Laminate slopes

Laminate - flooring, often used for slopes of the front door, it does not need to be further processed, it resists mechanical stress. Do-it-yourself decoration has a lot of nuances.

There are two ways to install laminate slopes:

Frame installation. With this technology, you can insulate the opening: fill mineral wool or mounting foam. The design flaw is that the slats are placed only in a horizontal position.
Glue installation. It requires a flat surface of the opening, or it must correspond to the dimensions of the laminate. The laminate is glued onto the foam (at low pressure).

The first method is preferable for apartments, the second is universal.

Slopes from MDF panels

Most common finish: Affordable, good looking, easy to install.

Necessary materials:

MDF panels.
Wooden bars, width 3 cm.
Dowel.
Self-tapping screws.
Liquid nails.
Platbands.
Decorative corner.
Guide bars.

Instruments:

Perforator.
Drill.
Scissors, knife.

Installation of MDF door slopes - do-it-yourself installation algorithm:

Clear the opening.
Drill holes around the perimeter for dowels.
After, attach the rails, guides.

Measure the dimensions and make templates for the details for the slopes.
Cut out details.
Install the top part on the screws. Check that there are no gaps.
Install in the guide side parts: inside on nails, outside on self-tapping screws.
Paste the outer corners with a flexible decorative corner to hide the screws, bumps.
Inside, paste over the corners with a decorative rail and the finish is ready.

After finishing work, you need to install platbands. If there is still wallpapering to be done, they are installed after the repair is completed.

Advantages: finishes look presentable, easy installation.

Slopes from sandwich panels

PVC sandwich panel is two thin sheets of plastic with a layer of insulation (sheet thickness 1 cm).

Materials, tools for installing slopes of PVC sandwich panels on the front door:

PVC sandwich panel.
Profile (starter, cover).
Liquid plastic.
Roulette.
Self-tapping screws.
Screwdriver.
Drill.
Screwdriver.

Installation of slopes from sandwich panels, or how to do it yourself:

Clean the opening from dust and foam residue.
Take measurements of the parts of the sandwich panels (length, width): one top, two side. For convenience, you can cut out a cardboard template so that there are no gaps between the parts of the PVC sandwich panels after installation.
Slice starting profile, attach to self-tapping screws (indentation 10 cm) along the edge. You can not use the profile: make an opening in the foam 1 cm deep, insert the edge of the sandwich panels there.
Install the top PVC panel.
After, cut the starting profile to the width of the slope, install under the ceiling and at the base of the floor. This can be omitted if there is liquid plastic - the cracks can be sealed with it. But do not use sealant - it darkens.
Installation of strips of sandwich panels.
Close the sections of the sandwich panels with a “cover” profile. Cut and install. An overlap is formed in the corners of the structure.
In the place of overlap, cut the profile at an angle of 45 degrees.

Optional space between sandwich PVC panel, the wall opening is filled with mounting foam. This is done after installing the sandwich panels.

More about installing slopes with your own hands after installing the front door, watch the video

Non-standard solutions

In addition to the above standard methods using popular materials, you can use more original variants that will emphasize the interior, decorate the front door and surprise your friends:

Artificial stone - non-standard slope finish. The main advantage is resistance to mechanical stress (if this is not a plaster model, it is fragile). Not a cheap option, requires the participation of a specialist.

Tile. A type such as clinker (imitation of brick or stone) is suitable.
Plastic panels are an affordable but unreliable finish.
Decorative plaster - in terms of aesthetics, endurance, it has no equal. But it will take some effort to find a good specialist in this area, because this work requires a creative approach and professionalism.

Materials can be combined if their properties are similar (sandwich panel details + stone, laminate + tiles and others).

No one wants to overpay when installing doors. That is why the decision is often made to make the slopes of the front door with your own hands and not to hire builders. If you approach the process with imagination, even a non-specialist can cope with the work.

Not always at home full set tools for all occasions. And apartment owners panel houses know very well how difficult it is to drill holes in concrete walls oh, still Soviet-built. Therefore, in some cases, you can sacrifice the correctness of finishing the slopes, greatly simplifying your work.

PVC slopes with and without frame

Perhaps the easiest, fastest and “cleanest” way to finish slopes is to decorate them with PVC panels. There are even universal panels on the market that combine a slope, a corner and a casing.

The advantage of this slope is the flexible connection between the panel itself and the casing, allowing it to be adjusted to walls with angles that deviate from 90 degrees.

The installation process of these slopes is simple to disgrace:

Due to the flexibility of plastic, such slopes can be installed even on uneven walls. But the ideal result will not work - gaps will necessarily form, and in places with an insufficient amount of mounting foam, the plastic will “walk”. But this is the fastest solution to the problem!

PVC slopes on a primitive wooden frame will look much neater and more reliable. You can even use PVC panels with a wood or stone design, without trimming at all.

For this:

To prevent the panels from slamming when the front door opens, the empty space between the bars can be filled with insulation of a suitable thickness or blown out with mounting foam. This will also provide additional sound insulation.

"Wet" way to finish the slopes with your own hands

Leveling and plastering slopes remains the most economical option. And even if everything does not work out perfectly, it will not affect their service life in the least. The process takes place in several stages:

Training:

Applying the screed:

cement mortar is mixed - you can do it yourself or buy it ready-made;
for 1 kg of cement, you need to take 1 kg of lime and 5 kg of sifted sand - the solution should be moderately thick and not spread, because they are leveled vertical walls and the top of the slope;

after the screed has dried, you can apply a regular primer and start applying the plaster.

Slope putty:

Decorative finish:

slopes can be painted or wallpapered, creating a monolithic canvas with walls;
in both cases, a primer is applied to the putty, and a decorative coating is already applied on top.

You should not try to save money and skip any of the steps - this will only worsen the final result and you will have to redo everything again.

Drywall slopes

If working with a puncher does not scare and bother cement screed if you don’t want to, you can decorate the doorway with sheets of drywall. This is especially true for houses with thick walls, where the slopes are very wide.

Gypsum board frame

In order for drywall sheets to be securely fixed and to withstand even artificial stone or tile finishing, you will need a wooden or metal frame:

For slopes of the front door, especially if it faces the street, it is better to use moisture-resistant drywall. It is also important to remember that there is always a small gap between the floor and the drywall to prevent drywall from getting wet. At decorative trim this gap will still be hidden.

Drywall slope on plaster

Instead of a GKL frame, it can be fixed with mounting foam with plaster. Isn't it strong enough? But if the load on the sheets is small, then the margin of safety should be enough. The technology itself is simple, even a layman can handle it:

What should not be forgotten when finishing slopes

Slopes are not only the aesthetic appearance of the doorway, but also its protection from drafts, moisture and noise. Therefore, regardless of the method of finishing, it is important not to forget:

Check the tightness of the door frame installation. To do this, it is enough with the door closed and open window hold around the perimeter with a lit candle. If the flame deviates to the side - in these places you need to add mounting foam.
Protect walls under overhead slopes from fungus and mold. For brick and concrete walls there is a special antiseptic primer, for wooden and frame walls do not forget about the vapor barrier device and processing wooden elements fire bioprotection.
Remove all debris and loose fittings from around the door, even when installing slopes on the frame. Otherwise, the abrasive dust left after the repair will still seep into the room, and periodically falling pebbles will add gray hair to impressionable residents.
To insulate the slopes of the door that goes directly to the street, and not to the dressing room. Otherwise, additional heating costs are provided.

Even slopes from MDF can be made without a puncher and excess debris. This is clearly shown in the video:

home » materials » How to close the front door after installation. Sealing slopes after installing the front door - how to seal and sheathe on metal