Heated summer shower - country comfort in any weather. Do-it-yourself country shower How to make a hot shower in the country

The best rest after hard work on your suburban area, this is a pleasant, warm, relaxing shower, which will not only have a calming effect, but also relieve the nervous tension that has accumulated over the whole day.

To install the shower use epoxy resin for the manufacture of which special fillers for resins are used.

Therefore, many gardeners equip their plots with summer showers.

Summer shower at your dacha

The outdoor shower stall is perhaps one of the most important buildings on the property. With it, you can not only wash your body after a whole day of work on your site, but also refresh yourself in the summer heat.

Before installing a shower cabin on your site, you need to choose the best place for this. The shower should be located at a small distance from the main building, most often behind the house.

After the owner of the site has decided on the area for the shower and the size of the shower cabin, he can proceed with the installation. This room must be at least 1 sq.m. area, but preferably a little larger.

If a shower dressing room is planned in order to undress and hang dry things, the building area is doubled. The height of the building is usually approximately 2.5 meters.

In general, the dimensions of our cabin are 1.0x2.0x2.5 m, this is the best option. If the installation of the cabin is planned from wood, then it is necessary to mount the frame using wooden beams or metal corners.

Walls in the shower better way ventilation should recede from the ceiling and floor by twenty centimeters. They can be built from materials left over after the main construction of the homestead.

Shower equipment with water supply

When installing a shower stall in your summer cottage, the owner needs to without fail think in advance how to equip the supply and drainage of water. Since the drainage and supply system is mounted at the time of laying the foundation of the future shower cabin.

Water in the shower is very often served from a source located at a remote distance. Such a source can be a well drilled on the site, or a standard water supply.

Nowadays, due to the presence of plastic pipes of small diameter, it will not be possible to connect the cabin to the main source of water supply. special work. What are the benefits of these pipes, they are more durable and do not rust and various erosions, like metal pipes.

They are sold in coils, and there is not much trouble during the laying of the pipe for the water supply, it is only necessary to provide a connection to the main source, which can be done with a small, rubber piece of hose.

Just as easy to connect plastic pipe with storage tank for shower. The advantage of such pipes is that if they were not installed thoroughly, they can be easily removed from the site for the winter period.

Shower drain

Water drainage after washing can be done different ways. Some owners summer cottages absolutely do not drain the water.

One of the most normal ways is to drain water into a centralized sewer, but, unfortunately, not every owner of a summer cottage has such an opportunity.

The best way, of course, is then the waste and drainage pit. This is inexpensive and allows wastewater to go deep into the ground. A pit for drainage water can be placed under the shower stall, or in close proximity to it.

It is dug to a depth of no more than 50-60 cm, the size of the sides is 1.0x1.0 m. After the pit is dug, the soil in it is tightly rammed and it is covered with rubble or broken bricks.

On top of the filled pit, put a plastic, steel or wooden pallet.

After that, a shower cabin is mounted. If the hole for Wastewater is nearby, it is best to make a tap from sewer pipe from plastic.

Photo ideas on how to make a summer shower in the country

We create a warm shower in the country: we find out the technical points

Of course, before you start building, you will have to make drawings of a warm shower in the country with your own hands in order to calculate all the materials, and in addition, the technical capabilities with which you are going to endow this building.

Indeed, often heated water occurs in such buildings only in hot weather, that is, it is heated naturally, depending on weather conditions, but it can also be forced heating.

Country shower with heating

It is about this forced method of heating water, as well as about the insulation of the architectural structure itself, that we want to tell you, and also bring to your attention in this article.

Warm shower box

How to supply hot water

The main problem for a shower that is separate from the house is hot or at least warm water - if this can be organized in a building from a common system, then autonomy is needed here. In this case, the most convenient option is a flow-through electric heater, because almost any Vacation home connected to the mains, therefore, the installation of such a device is a minor technical problem, where the safety instructions against electric shock must be observed.
Let's say right away that this is not some kind of super option - the device does not heat water to a very high temperature, especially if it is cold, but, given the very specifics of a country shower, warm water will be enough for you. In most cases, even if the price of the device is high, it will not heat water above 40 ⁰C, but you are unlikely to need more.
Another option is an underlay. hot water from the house- pipes are laid underground and insulated, but during transportation too much heat loss occurs, and if this does not bother you, then this option is better than the first one.

How to heat a shower

Infrared wall heaters

Of course, in the summer you will not have a question about how to heat the shower stall - it will already be warm or even hot there, but in spring or autumn, when you plant a garden or harvest, in your shower you will most likely feel too chilly. But you can make such a box with heating, and here, infrared heaters are the best suited for heating, and there are good reasons for this.

Firstly, the IR panel will heat up a small room very quickly, since there is a special principle of giving off heat calories - the panel will not heat the air, but nearby objects, which will just become a source of heat.

Secondly, such devices can be installed in any place convenient for you - on the floor, on the ceiling and on the wall, and, thirdly, they can be easily turned off and removed. This very “third”, perhaps, is the dominant factor in favor of IR systems - they will not be stolen, since you will have the opportunity to bring them into the house for the winter, or even take them to the city.

Note. Infrared heaters There are not only different capacities, but also different configurations.
That is, it can be a device in the form of a panel, but it can also be a film type - the latest models can be installed under wall and ceiling cladding.

How to keep warm in the country shower

Insulation of the box with foam

So, we need an insulated shower in the country, that is, given that our construction will be quite simple, most likely from boards or OSB, this will not be enough to keep the cold from the street inside. Two materials are best suited as thermal insulation here - mineral wool(glass or stone (basalt), but not slag) and polystyrene (in extreme cases, extruded polystyrene foam, but it is much more expensive).

The process of laying such insulation is actually no different from installation in other rooms - all the same frame and fasteners that are most suitable for the material used.

But there is one very important nuance, which arises in connection with the specifics of the shower box - it is constantly humid there, therefore, the thermal insulation must be protected from water splashes. If you are doing installation from the side of the street, then this question disappears, as it were, by itself, but inside it is extremely important, otherwise you risk getting fungus and mold there.

Foil - excellent waterproofing

So, it is best to cover the insulation with an ordinary thick cellophane film, and then cover this entire structure with foil or any thin foil insulation, as shown in the photo above. Here you immediately, as it were, "kill two birds with one stone" - protect the insulation from moisture penetration and create an infrared reflector.

The fact is that the foil has an excellent property - it reflects infrared rays, therefore, the excess of heat calories in boxing will be minimal.

Note. It is very important that you insulate not only the walls, but also the ceiling, since according to the laws of physics, heated air rises and if there is poor thermal insulation, then warm air fade away very quickly.
The same applies to the waterproofing of the ceiling - the steam, rising up, will be reflected by the foil insulation.

Plumbing nuances

Since we are insulating the shower box on the street, it is quite natural that we will not make a drain (lattice) floor there, since cold air will flow from below and all heating will be useless. In such cases, of course, it is best to fill the floor concrete screed with insulation, which is most often used as an expanded clay pillow laid on a layer of sand.

That is, the screed is poured here according to all the rules - the soil is planned, then a waterproofing film is laid with a twist on the walls, then a layer of sand 2-3 cm is poured and after that - an expanded clay cushion, the thickness of which depends on the coldness of the soil, but not less than 4-5 cm.

Do not think that we have made a reservation about the waterproofing of the shower floor - the film is needed here not so that water does not get into the soil, but so that the pillow is dry - thereby reducing the thermal conductivity of materials.

You will need to mount a drain on the floor and take it to the public sewer, to a septic tank, or dig it nearby cesspool, only it should be used exclusively for soapy water. But still, the best option would be a septic tank - you will not only not pollute the soil, but also will not breed unpleasant odors, which exudes stagnant water.

Conclusion

You understand that building a wooden box is easy enough, but how to make it so that you can wash in it during the cold season is a completely different question. So such a seemingly insignificant building in this case will turn out to be a capital object, but if you bring water underground, you can wash there at any time of the year.

http://hydroguru.com

Indeed, often heated water occurs in such buildings only in hot weather, that is, it is heated naturally, depending on weather conditions, but it can also be forced heating.

It is about this forced method of heating water, as well as about the insulation of the architectural structure itself, that we want to tell you, as well as bring to your attention the video in this article.

Warm shower box

How to supply hot water

The main problem for a shower that is separate from the house is hot or at least warm water - if this can be organized in a building from a common system, then autonomy is needed here. In this case, the most convenient option is a flow-through electric heater, because almost any country house is connected to the mains, therefore, the installation of such a device is a minor technical problem, where the safety instructions from electric shock must be observed.
Let's say right away that this is not some kind of super option - the device does not heat water to a very high temperature, especially if it is cold, but, given the very specifics of a country shower, warm water will be enough for you. In most cases, even if the price of the device is high, it will not heat water above 40 ⁰C, but you are unlikely to need more.
Another option is a hot water supply from the house.- pipes are laid underground and insulated, but during transportation there are too large heat losses, and if this does not bother you, then this option is better than the first one.

How to heat a shower

Of course, in the summer you will not have a question about how to heat the shower stall - it will already be warm or even hot there, but in the spring or autumn, when you plant a garden or harvest, in your soul it will most likely seem too chilly. But you can make such a box with heating and here, they are the best fit and there are good reasons for this.

Note. Infrared heaters come in not only different power, but also different configurations.
That is, it can be a device in the form of a panel, but it can also be a film type - the latest models can be installed under wall and ceiling cladding.

How to keep warm in the country shower

So, we need an insulated shower in the country, that is, given that our construction will be quite simple, most likely from boards or OSB, this will not be enough to keep the cold from the street inside. Two materials are best suited here as thermal insulation - mineral wool (glass or stone (basalt), but not slag) and polystyrene foam (in extreme cases, extruded polystyrene foam, but it is much more expensive).

The process of laying such insulation is actually no different from installation in other rooms - all the same frame and fasteners that are most suitable for the material used.

But there is one very important nuance here, which arises in connection with the specifics of the shower box - it is constantly humid there, therefore, thermal insulation must be protected from water splashes. If you are doing installation from the side of the street, then this question disappears, as it were, by itself, but inside it is extremely important, otherwise you risk getting fungus and mold there.

Foil - excellent waterproofing

The fact is that the foil has an excellent property - it reflects infrared rays, therefore, the overexpenditure of heat calories in boxing will be minimal.

Note. It is very important that you insulate not only the walls, but also the ceiling, because according to the laws of physics, the heated air rises and if there is poor thermal insulation, then the warm air will evaporate very quickly.
The same applies to the waterproofing of the ceiling - the steam, rising up, will be reflected by the foil insulation.

Plumbing nuances

Since we are insulating the shower box on the street, it is quite natural that we will not make a drain (lattice) floor there, since cold air will flow from below and all heating will be useless. In such cases, of course, it is best to fill the floor with a concrete screed with insulation, which is most often used as an expanded clay pillow laid on a layer of sand.

Do not think that we made a reservation about - the film is needed here not so that water does not get into the soil, but so that the pillow is dry - thereby reducing the thermal conductivity of materials.

You will need to mount a drain on the floor and take it to the general sewer, to a septic tank, or dig a cesspool nearby, only use it exclusively for soapy water. But still, the best option would be a septic tank - you will not only not pollute the soil, but also will not dilute the unpleasant odors that stagnant water exudes.

Conclusion

In the summer, even when resting, and not working, the opportunity to wash is necessary in the country. The easiest way to organize this is on the street, and not in the house. You can make a portable - mobile shower. This great option for the first time. But I want something more solid. For this they build Summer shower in the country. Although it is stationary, it is lightweight.

Portable summer

Let's start with the simplest models, which do not even require cubicles or large capacity devices. There are mobile showers that work on the principle of a foot pump. The source of water is any container that you put next to you - a bucket, a basin, a tank - whatever you have. You lower the end of the hose connected to the foot pump into it, which most often looks like a rug.

Foot summer shower - toptun

A hose with a watering can is connected to the outlet of this "pump". To get a stream of water, trample on the mat alternately pressing the pump pads. We trampled - the water went.

What is good about this option is that you can carry it with you. It's warm outside - wash on the lawn. It got colder - they went into the house, put a trough, washed themselves there. You can also take this shower on a hike - it fits in a standard package. Another plus is that you can regulate the temperature of the water yourself: if you pour it warmer, you wash yourself in warm water. If you want to freshen up, take a bucket of cooler water. A good option for a shower for summer use.

Summer stationary shower in the country

When installing a stationary shower, the first question arises: where to drain the water. If there is already a drain pit for, you can lay a pipeline there. But this solution is not the best if you are using bacteria or waste treatment products in the pit. In this case, a certain humidity is required, and with a shower it will be clearly more than normal.

For the shower, it is better to make a separate drain hole. If the soil has normal drainage capacity, it is enough to dig a hole about 60 * 60 * 60 cm nearby, fill it with expanded clay, or you can use broken bricks. This should be enough for the average water consumption. If your family belongs to the category of "waterfowl" or the water goes badly, make the hole bigger.

On sandy soils, you may encounter another nuisance: sand can crumble. Then the walls can be strengthened with a net by driving pegs on the sides. Another option is to sheathe the walls with boards (as in the photo). But this is if the board is in the remnants.

Base

Whatever the summer shower, it usually weighs a little. Therefore, the basis for it is not made too serious: there is no point in burying money. Most often, small foundation blocks are used, which are set according to the level. The shower in the country is raised above ground level by 20 cm or so. This is enough so that the treated wood (if it is used as a frame) does not rot.

If you are going to cook the frame from metal, you can put it in general on the level paving slabs or stove. If desired, you can cast the columns yourself: put the formwork, lay the reinforcement and pour concrete.

frame

The dimensions of the soul are chosen arbitrarily: there are no standards here. In addition, the shower cabin is often only one of the parts. In another, they arrange, for example, a locker room or a room for a water heater (electric or wood-burning - according to the conditions). Someone plans to take the other half under the pantry or store inventory. So a country shower is not always just a booth "for washing."

If you plan a lightweight design in which they will only wash themselves, and the simplest option is with a curtain instead of a door, you can take the minimum dimensions: a square with a side length of about 90 cm (drawing below), the height of the racks excluding the tank is 2.2 m or higher (if the family is tall).

But such a width is far from convenient: it is too crowded even for people of average build. It is more comfortable with a minimum width of 100 cm, and preferably 120 cm. This frame is assembled from metal or wooden blocks.

metal

The metal frame for the shower is boiled from a corner with a thickness of at least 4-5 mm. The width of the shelf is chosen depending on the planned load. The frame is usually loaded with water tanks and sheathing. If you plan to put a plastic square container of 100 liters on top, and cover the walls with a film, impregnated cloth or something equally light, you can take the section to a minimum. If you plan, for example, two 200 liter barrels, and sheathe the shower cubicle in the country house on both sides with clapboard, the load will be completely different. And here large sections are required.

Yet metal carcass for a country shower can be made from a profiled pipe. The wall thickness for the racks is 3 mm, 2 mm is also suitable for strapping. It has a rectangular or square section, which greatly facilitates the fastening of the crate and sheathing. To attach something to a corner, it is often necessary to first screw the bars to it, and attach the rest of the strapping to the bar. The piping can be fastened directly to the profiled pipe - with bolts or screws with pre-drilled holes.

The metal frame is best welded. If there is no apparatus, you can make a collapsible frame on bolted joints. Craftsmen do it this way: they cut pipes of the required length, take thick mounting angles and assemble the frame with bolts.

In case you plan to learn how to weld metal, the choice welding machine — .

from wood

A wooden frame for an outdoor shower is assembled from a bar. For bottom strapping use, as a rule, pine timber 100 * 100 mm or 150 * 100 mm. Racks can be set to a smaller section. Again, it depends on the load. If the tank on the roof is voluminous, make racks from weaving. If they hold only the roof (water is heated in titanium nearby) or a very small tank, then 50 * 50 is enough.

You can attach the bars in different ways. If correct, you need to cut a spike and a groove. If in a quick way, you can dock directly, reinforcing the connections with corners.

Having set the racks, they immediately make the upper harness. It already definitely goes 50 * 50 mm or 50 * 40 mm. They also make intermediate strapping. There may be one, two, or even three. If you are going to sheathe the shower with clapboard, imitation of a beam, it is better to fasten the crossbars more often: it will be possible to more tightly fit not quite even lumber. The quality of wood materials sold on the market is, to put it mildly, low. We have to correct the jambs of geometry due to force.

The construction of a frame from a bar is shown in the video

sheathing

You can fit the frame with any material:

You can use any other fence that comes to your mind and will perform its functions. For example, in one summer cottage, the shower sheathing was woven. Type .

shower tank

As a tank for a summer shower, use any suitable container that is on the farm. Most often - this is a barrel - metal or plastic. If there is nothing suitable, you can buy a container. They are available in a large assortment: plastic, metal - from ferrous metal and stainless steel.

Not everyone likes plastic ones, since water heats up worse in them. For the southern regions, this is not scary - there is already enough heat, but for Middle lane-may be critical. Although in this region, most of the summer, water even in black metal barrels requires heating. On the other hand, plastic containers are inexpensive, light, there are square flat shapes, which means they fit well on the shower frame and there is no need to invent a method of attachment.

IN metal barrel water will heat up faster, especially if it is painted black. But if it is made of ordinary metal, there will be a lot of rust by the end of the season. So much that it will be noticeable on the body. This is the main disadvantage of such tanks. Much better than stainless steel. If finances allow, allow yourself one.

Summer shower tray

There are two options for a country shower device: when the septic tank (drain hole) is located directly under the shower stall. Then you can simply make a pouring floor: lay boards with a gap of 3-5 mm. A simple option that works great on sandy and sandy soils. In this case, the water leaves very quickly, without stagnation anywhere, therefore such a device does not cause any inconvenience.

But this option is only suitable if you plan to use the shower only in warm weather. And spring-autumn will not go - it will be cold, as it will blow from below.

If a normal drain is required or you need to divert the drains to the side (drain pit away from the building), you need to make a pallet in the shower. The easiest case is to buy ready-made. Then, during the construction and selection of frame sizes, you will have to focus on the size of the pallet: under it you need bars to which it is attached. They also connect it as standard: they put a siphon with flexible hose like in the bathroom.

If the pallet is plastic, just bars around the perimeter will not be enough: support is required under it, otherwise it “walks” too much. This foundation is usually laid out of bricks. You can bind them with a solution. Just remember to leave room for the drain hose.

In some cases, they try to make a more solid drain: without using a finished pallet. In this case, fill concrete slab. To do this, they dig a pit of the required size, with a depth of about 30-40 cm. A layer of gravel 15-20 cm thick is laid on the bottom. Already at this stage, a mortgage is installed - a drain pipe and a drain grate. They put up formwork. It can be non-removable - made of brick. Crushed stone is rammed, everything is poured with concrete (). A week (at a temperature of + 17 ° C and above) is waiting for the base to gain strength. After you can continue work: put the frame and continue construction.

Tank filling and water heating

Filling the shower tank with water is usually not a problem. Sometimes they carry water in buckets - if you want to wash, you will carry it. Not very convenient, of course, but it happens ... If there is water supply in the country, they fill it with a hose, install a supply pipe with a valve. It is necessary to add water - open the tap, the tank is full - closed.

How to autofill a tank

The most advanced do automatic filling. Then the water supply is opened / closed by a float system similar to the one in the tank. Only in the event of a breakdown, it is necessary to provide for the drainage of excess water. And, preferably, when leaving the cottage, shut off the supply tap. And then you can turn your own and neighbor's cottage into a swamp.

An exemplary scheme for the implementation of auto-filling the tank is shown in the figure above. Please note: water is taken into the shower close to the surface: here is usually the most warm water. Only this pipe is placed at the opposite end from the cold water inlet, otherwise the water will still be cold.

Two pipes go to the sewer: one overflow (mustard color). With its help, the tank will not overflow in the event of a breakdown of the float mechanism. The second drain into the sewer for a complete drain (brown). It will come in handy during the conservation of the system - draining for the winter, therefore a crane is installed on it.

Organization of heating

The easiest option is to use solar energy. Yes, it heats water through the walls of the tank. But the water column is too large for it to warm up quickly. Therefore, people come up with various installations for solar water heating.

As mentioned above, in the tank the warmest water is at the top. And the traditional feed comes from the bottom. That is, we take the most cold water. In order for the warmest water to enter the watering can, a hose is attached to it, and it is attached to a piece of foam that I let float. So the water intake is from above.

To speed up the heating of the water, they make a “coil” (in the photo above, this is the right figure). At the bottom of the water tank and above, two pipes are welded in one of its walls. A black rubber hose is connected to them, which is folded in rings in the sun. If there is no air from the hose, the movement of water will be quite active.

If the sun is not enough for you, but you can bring electricity to the soul, you can use heating elements (wet). We need them with a thermostat so that you can set the desired temperature. Usually used in storage water heaters so you can find it.

When you pull the power line to the shower, do not forget to install an automatic device with an RCD. This is the minimum that will ensure your safety.

Building a shower in the country: a photo report

It was decided to use a fence at the far end of the site as one of the walls of the shower. It was decided to do a shower with a locker room - it's much more convenient.

The soils are sandy, the water drains very quickly, so only one tire was buried for draining. Shower tests have shown that no more is required. Much more water was poured than in my barrel, but no puddles were observed.

Then the frame was welded. A rectangular pipe 60 * 30 mm was used. It's a bit too much for this design, but they used what was: the remains of the construction of the fence.

Having welded the floor frame, and having indicated its level, they formed a drain. They reported the missing height with a brick (battle, remnants). Everything was filled with concrete, forming a drain into the tire.

Leveled the floor and in the second half, left to set. Started working on wood. Purchased aspen board. She was first treated with a skin fixed on a grinder. After impregnated with a protective composition.

While the impregnation dries, we continue to cook the metal frame for the shower. The middle harness was welded from the same profile pipes. Then it was used as a scaffold for working at height. Already dried boards were placed on the strapping pipes. From this pedestal, the upper harness was cooked.

The frame is almost ready. It remains to weld the frame under the barrel at the top.

The metal used is old, so it's covered in rust. She was cleaned off by a grinder. Then the frame of the shower was painted three times with rust paint. It was chosen in blue, as it was planned to sheathe the shower with blue polycarbonate.

Polycarbonate was mounted on self-tapping screws. During installation, neither special nor ordinary washers were used. This is a violation of technology, which can lead to the fact that in sunny weather it will crack. This material has a large thermal expansion, which is enhanced, since in this case it is fixed on a metal frame.

The barrel in the barn has been washed. Pipes are welded to it. One is for filling water, the second is for connecting a watering can. After that, the barrel was painted black.

Most summer residents think about creating a shower in the country with their own hands.

Firstly, it is an opportunity to improve comfortable conditions without high costs.

Secondly, a properly equipped outdoor garden shower allows you to meet the necessary sanitary needs, as it is suitable for use at any time of the year.

And besides, crafts for decorating it make any garden area exclusive.

Design features

If the shower will be used exclusively in the summer, then a simple quick-mounted structure, such as a shower rack, a camp shower or a toptun, is sufficient.

You can install a simple camping summer shower with your own hands in a fairly short time.

If long-term operation is planned, including in the cold season, then it is necessary that the design of the craft shower be reliable and provide for the possibility of installing equipment for heating not only water, but also air in the cabin.

It is more difficult to install a winter shower in the country with your own hands, since its design needs a frame and a foundation.

Regardless of the modification suburban option The structure includes the following:

base or foundation;
drain ladder or drain;
pallet and floor;
cabin;
holder-diffuser and stop valves;
pipeline;
devices for pumping and heating water, as well as for heating the cab.

As a material for such crafts as a country shower room without a foundation, film or plastic is used.

For booths installed on the foundation, it is preferable to choose more durable materials - wood or brick. A good option- do-it-yourself polycarbonate shower.

The most famous modifications of the shower craft used in summer cottages:

Toptun - mat with pump and hose. The water supply is provided by pressing the feet on the mat;
Camping - a compact portable plastic container equipped with a hose and nozzle. It can be stationary, mobile;
Circular. The circular option provides water supply from all sides;
Alekseev. Provides hydromassage by supplying water under high pressure;
Tropical. The flow of water entering through a special grate looks like a tropical downpour.

Making a circular shower with your own hands is quite difficult, but the result of this work will please any summer resident.

Toptun - the most popular shower among summer residents

Simple designs-crafts of shower devices intended for summer operation are considered the best solution to the issue of country hygiene.

After all, installing the same circular or tropical shower is not as easy as it might seem at first glance. That is why, choosing which shower to make in the country with their own hands, summer residents most often stop at a trample.

To build a toptun shower with your own hands, you will need a car pump, two corrugated hoses, a container with a lid, and a shower head. You don't even need a holder.

The sequence of operation of the toptun:

Water of the required temperature is drawn into the container. Considering that the volume of the container is small, a do-it-yourself shower tray, if it is a toptun, is not needed;
Crafts are attached to the lid - a wooden or rubber cork equipped with holes and tubes, the diameter of which corresponds to the diameter of the hoses;
The container is covered with a lid with attached hoses - one from a car pump, the second - a shower head holder. Under the pressure of air from the pump, water enters the hose. The watering can is held in the hand or attached to any surface.

By the same principle, you can make a camping summer shower. To do this, you will need a rubber mat or pedals equipped with built-in valves, as well as two hoses.

As a container for water, an ordinary bucket is used, covered with a lid, in the hole of which the inlet hose-holder of the watering can is fixed.

As in the first option, the pallet is not required, and the earth replaces the drain drain.

The water supply to the hiking version is carried out by alternately pressing the pedals with your feet.

Each step provides one serving of water. As a rule, the marching method saves water and is used in conditions with limited access to water resources.

Also, a camping outdoor shower can be used to wash a car.

A circular shower can be considered as another option for a country house, but in this case, the actions listed above will not be enough. You will need a special holder for it.

How to expand functionality?

The functional purpose of a shower room, even in summer cottages, should not be limited solely to hygienic considerations.

For many summer residents - this is an important part of the suburban area.

But not everyone knows that a do-it-yourself country tropical shower in a bath can fully replace many of the procedures offered by spa salons.

In practice, available functionality shower is the result of choosing its variety.

That is, in order for the built country shower in the bath to live up to expectations, you need to learn more about its functionality and installation steps.

In the minds of most people, a bathhouse is associated with a healthy lifestyle, and visiting it is considered a preventive measure.

Therefore, the famous shower of Alekseev will come in handy in the bath.

Alekseev's shower is a new generation design, an analogue of the well-known Charcot's shower with hydromassage properties.

But Alekseev's shower, an invention of the Russian doctor of the same name, is equipped differently and has no analogues in the world in terms of the effectiveness of the impact.

The use of a device created according to the Alekseev method provides healing through massage and is recommended for many diseases.

To independently install Alekseev's shower in the bath, you need to understand how it works.

The unique difference of the device is the high-speed streams formed using the special design of the holes in the nozzle for the watering can.

If you make such a nozzle yourself, then installing Alekseev's device in your own bath is not difficult.

To do this, it is necessary to drill cone-shaped holes in the nozzle for the watering can - wide on the side of the water flow and tapering towards the outlet.

Then the craft nozzles are installed on the holder. The holder must be chosen carefully.

Considering that Alekseev's device gives a strong flow of water, care must be taken that the ladder ensures its full drain, or use a pallet.

At the same time, Alekseev's shower can be operated not only in a summer cottage, but also in an apartment.

Features of self-installation of various types

The functions of the device used in summer cottages can be expanded if you use the non-standard capabilities of its structural varieties.

For example, a circular shower, along with hygiene, will also provide a healing effect.

According to the principle of the device, the circular type of shower is a few systemically located pipes equipped with small holes and a faucet.

In the center is a holder with the main watering can. With the help of a tap, the water supply pressure is regulated.

Thus, the circular shower additionally provides a comprehensive hydromassage of the body.

You can install such a device yourself both in the country and in the apartment.

To create an original shower craft, it is necessary to connect several pipes equipped with small holes in series with the central riser, on which the mixer holder is located.

In shape, the circular type of shower resembles the back of a chair with transverse or longitudinal crossbars.

Then you should take care of the flow of water - the ladder will cope with this task. The owner of the cottage has the right to decide whether he needs a pallet in this case, or a ladder will do just fine.

An excellent alternative to a regular shower can be a rain shower. This is a device whose water flows mimic a tropical downpour.

Functionally, the tropical shower type is a hydromassage device.

However, not every apartment has the opportunity to install a rain shower, but if such a design is installed in the garden, the impression of authenticity will be complete.

It is not difficult to build a rain shower in the country on your own. To do this, it is enough to increase the area of \u200b\u200bthe watering can of the mixer and strengthen its holder.

A ladder will help control the discharge of a powerful stream of water, which distinguishes a rain shower. It is also convenient to use a deep pan.

But you need to remember that both the holder, and the ladder, and the watering can must be of high quality.

Construction stages

To build a summer shower with your own hands, you need to know the basic rules of the process:

Preparation - determine the dimensions and draw a diagram;
Choice of location - a sunny place on a hill, which is not too far from the house and the water supply, but with the possibility of arranging a drainage system if a ladder is provided in the shower equipment, or a drain pit if a pallet is installed;
Construction of the foundation - level the site equal to the size of the building, then fill it with concrete;
Installation of the frame - piles are installed and fixed at the corners of the site, then they are tied up, constructing the shower floor. The racks of the frame are fixed with self-tapping screws. Build walls and roof;
Summing up communications - installation of a tank, equipment for draining, lighting and ventilation;
Mount pipes and a pallet - it is necessary to drain water. Sometimes they do not use a pallet, but a floor in which a large ladder is mounted. The best option drain systems - a ladder with a lock and a grate. The shower drain performs the function of a sewer, but may have a different throughput;
Waterproofing, wall cladding. For operation in the cold season, the walls need to be insulated;
Decorative shower cubicle. beautiful crafts increase the aesthetic appeal of the entire suburban area.

If the weight of the structure is small, then a foundation is not required for its installation. For example, a metal frame for a polycarbonate booth is installed on fittings driven into the ground.

In addition, it is physically easier to build a do-it-yourself polycarbonate shower than a brick one.

A properly built base will allow you to upgrade your shower room in the future and enjoy its new possibilities endlessly.

home » Roof installation » Heated summer shower - country comfort in any weather. Do-it-yourself country shower How to make a hot shower in the country